RF Amplifiers
RF Wideband Pre-Amplifiers
RF Driver Amplifiers
DC Coupled Amplifiers
DC Coupled Power Amplifiers
Trans-conductance Amplifier/Current Injector
Wideband RF power amplifiers and RF signal generators are critical components in both radiated and conducted immunity tests. The combined cost of the requisite immunity test equipment is prohibitively expensive for pre-compliance applications.
Tekbox created a low-cost solution comprised of modulated RF power amplifiers driven by spectrum analyzer tracking generators. Our amplifiers include built-in modulators that produce the typical modulation forms defined by the applicable standards, as tracking generators provide a CW output signal: 1 kHz, 80% AM, 1 kHz, 50% duty cycle PM, 217 Hz, 12.5% duty cycle PM.
Our EMCview software controls the frequency and output power of the tracking generator during testing.
Depending on model, our amplifiers currently cover the frequency range from 100 kHz to 1.5 GHz and the available output power covers the range from 150 mW to 25 W.
The modulated amplifiers are suitable for pre-compliance radiated immunity testing in TEM cells and pre-compliance conducted immunity testing with CDNs or bulk current injection probes.
Modulated RF Power Amplifiers
![]() | ![]() | ![]() | ![]() | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|---|---|
| Model | TBMDA1 | TBMDA2 | TBMDA3B | TBMDA4B | TBMDA5 | TBMDA7 | TBLPA1 |
| Frequency range | 40MHz-3GHz | 10MHz- 1.5GHz | 10MHz-1GHz | 100kHz-75MHz | 150kHz-1GHz | 1GHz-3GHz | 10MHz-1GHz |
| Output power | 150 mW | 0.5 W | 8 W | 5 W | 2.5 W | 400 mW | 1 W |
| Modulator | AM,1kHz,80%, PM,1kHz,50%, PM,217Hz,12.5% | AM,1kHz,80%, PM,1kHz,50%, PM,217Hz,12.5% | AM,1kHz,80%, PM,1kHz,50%, PM,217Hz,12.5% | AM,1kHz,80%, PM,1kHz,50%, PM,217Hz,12.5% | AM,1kHz,80%, PM,1kHz,50%, PM,217Hz,12.5% | AM,1kHz,80%, PM,1kHz,50%, PM,217Hz,12.5% | – |
| Gain | 22 dB | 43 dB | 42 dB | 48 dB | 38 dB | 40 dB | 32 dB |
| Application | Immunity pre-compliance testing in TEM-cells | Immunity pre-compliance testing in TEM-cells | Immunity pre-compliance testing in TEM-cells | Immunity pre-compliance testing in TEM-cells | Immunity pre-compliance testing in TEM-cells or with CDNs according EN 61000-4-6 | Immunity pre-compliance testing in TEM-cells | General Purpose |
| Maximum stress levels | TBTCO:100 V/m TBTC1:56 V/m TBTC2:28 V/m TBTC3:18V/m (CW) | TBTCO: 178 V/m TBTC1:100 V/m TBTC2:50 V/m TBTC3:33 V/m (CW) | TBTCO: 711 V/m TBTC1:398 V/m TBTC2:199 V/m TBTC3:132 V/m (CW) | TBTCO: 565 V/m TBTC1:316 V/m TBTC2:158 V/m TBTC3:105 V/m (CW) | Level 1 Level 2 (lim. freq.) | TBTCO:150 V/m TBTC1:80 V/m TBTC2:n.a. TBTC3:n.a. (CW) | – |
| Supply | USB | USB | Mains 100 – 240V AC | Mains 100 – 240V AC | Mains 100 – 240V AC | USB | Mains 100 – 240V AC |
| Product Page | TBMDA1 | TBMDA2 | TBMDA3B | TBMDA4B | TBMDA5 | TBMDA7 | TBLPA1 |
![]() | ![]() | ![]() |
|
|---|---|---|---|
| Model | TBMDA-CDN25 | TBMDA-BCI25 | TBMDA-BCI100 |
| Frequency range | 150kHz-250MHz | 1MHz-400MHz | 1MHz-400MHz |
| Output power | 25 W | 25 W | 100 W |
| Modulator | AM,1kHz,80%, PM,1kHz,50%, PM,217Hz,12.5% | AM,1kHz,80%, PM,1kHz,50%, PM,217Hz,12.5% | AM,1kHz,80%, PM,1kHz,50%, PM,217Hz,12.5% |
| Gain | 47 dB | 47 dB | 52 dB typ. |
| Application | Immunity pre-compliance testing with CDNs or BCI probes according EN 61000-4-6 | Immunity pre-compliance testing with BCI-probes according ISO 11452-4 | Immunity pre-compliance testing with BCI-probes according ISO 11452-4 |
| Maximum stress levels | Level 1 Level 2 Level 3 | substitution method: Level I (AM, CW) Level II (AM, CW) Level III (CW) Level IV (CW) | substitution method: Level I (AM, CW) Level II (AM, CW) Level III (AM, CW) Level IV (AM, CW) |
| Supply | Mains 100 – 240V AC | Mains 100 – 240V AC | Mains 100 – 240V AC |
| Product Page | TBMDA-CDN25 | TBMDA-BCI25 | TBMDA-BCI100 |
RF wideband pre-amplifiers
![]() | ![]() | ![]() |
|
|---|---|---|---|
| Model | TBWA2/20dB | TBWA2/40dB | TBHDR1 |
| Frequency range | 1.5 MHz-6 GHz | 2.5 MHz-6 GHz | 30 kHz-1.5 GHz |
| Gain typ. | 20 dB | 40 dB | 20 dB |
| Max. input power | +10 dBm | -10 dBm | +10 dBm |
| P1dB typ. | +18 dBm @ 2 GHz | +18 dBm @ 2 GHz | +18 dBm @ 100 MHz |
| Output IP3 | +33 dBm @ 2 GHz | +33 dBm @ 2 GHz | + 38 dBm @ 100 MHz |
| Noise figure | +5 dB | +5 dB | 2.7 dB |
| Power supply | +5V / 110mA, mini USB-B | +5V / 210mA, mini USB-B | +5V / 100mA, mini USB-B |
| Application | General purpose pre-amplifier near-field probe pre-amplifier | General purpose pre-amplifier near-field probe pre-amplifier | General purpose / high dynamic range pre-amplifier |
| Product Page | TBWA2/20dB | TBWA2/40dB | TBHDR1 |
RF driver amplifiers
![]() | ![]() |
|
|---|---|---|
| Model | TBDA1/14dB | TBDA1/28dB |
| Frequency range | 40 MHz-3 GHz | 40 MHz-3 GHz |
| Gain typ. | 14 dB | 28 dB |
| Max. input power | +20 dBm | +6 dBm |
| P1dB typ. | +22 dBm @ 1GHz | +22 dBm @ 1GHz |
| Output IP3 | +43 dBm @ 2GHz | +43 dBm @ 2GHz |
| Noise figure | +4 dB | +4 dB |
| Power supply | +5V / 115mA, mini USB-B | +5V / 225mA, mini USB-B |
| Application | Immunity testing in TEM cells, driven by a modulated RF signal generator | General purpose pre-amplifier near-field probe pre-amplifier |
| Product Page | TBDA1/14dB | TBDA1/28dB |
DC Coupled Amplifiers
![]() | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|
| Model | TBLNA-110M-50 | TBLNA-110M-HZ | TBCS101-TGA | TBCS101-DA |
| Frequency Range | DC-110 MHz | DC-500 MHz | DC-20MHz | DC-110 MHz |
| Gain typ. | 40 dB | 0dB / 20 dB | 20 dB | 1:50 |
| Input Impedance | 50 Ω | 1 MΩ // 20 pF | 50 Ω | Differential, 1M Ω//10pF |
| Max. Input Power | +30 dBm | 50 Vpp | +20 dBm | ±50V |
| P1dB typ. | +15 dBm | +8.6 dBm | +15 dBm | n.a. |
| Power Supply | 12V DC | 12V DC | +5V, USB-C | +5V, USB-C |
| Application | Pre-amplifier for TBMR-110M measurement receiver | Impedance converter HighZ to 50 Ohm in-circuit measurements in 50 Ohm systems, using oscilloscope probes | driver amplifier for CS101 setups | Differential amplifier for CS101 setups |
| Product Page | TBLNA-110M-50 | TBLNA-110M-HZ | TBCS101-TGA | TBCS101-DA |
DC Coupled Amplifiers
![]() |
|
|---|---|
| Model | TBDCA1 |
| 3 dB bandwidth | DC – 3 MHz, useable up to 10 MHz |
| Nominal output power | 150 W @ RLOAD ≤ 2 Ω 80 W @ RLOAD = 4 Ω 30 W @ RLOAD = 12 Ω |
| Max. output voltage | 56Vpp |
| Max. continuous output current | 10 Arms |
| Max. output current | 20 Arms for 30 seconds |
| Min. output impedance | 0.5 Ω |
| Output offset voltage | adjustable; ± 25 V |
| Application | General purpose output amplifier for arbitrary waveform generators Stress testing according to ISO 16750-2 and ISO 7637-2 Power supply input impedance measurement Structure current injection for MIL-STD-461H, CS109 Voltage ripple injection for MIL-STD-461H, CS101 or RTCA/DO-160 Section 18 Immunity testing according to ISO 11452-10, SAE J1113-2 and various automotive manufacturer specific standards RF power amplifier to drive Helmholtz coils or loop antennas |
| Product Page | TBDCA1 |
Trans-conductance Amplifier/Current Injector
![]() |
|
|---|---|
| Model | TBRFCI1 |
| Frequency Range | DC – 50 MHz, useable up to 100 MHz |
| Transconductance | 0.1 A/V, 1 A/V |
| Product Page | TBRFCI1 |



















